JBL 2206H 12" Woofer High Power LF Cone Transducer 600W Vented Gap Cooling

JBL 2206H 12" High Power LF Cone Trnasducer

2206H Key Features:

600 W continuous pink noise power capacity
100 mm (4 in) edgewound aluminum ribbon voice coil
45 Hz - 3.5 kHz response
95 dB sensitivity, 1 W, 1 m (3.3 ft)
SFG magnet structure with Vented Gap Cooling’” technology1
The JBL 2206H/J low frequency transducer represents the results of
JBL’s latest engineering research in high power transducer design. The
2206H/J signifies a major advance in speaker design by incorporating JBL’s
patented Vented Gap Cooling’” technology in an improved Symmetrical
Field Geometry (SFG) magnetic structure.

To increase power handling while reducing power compression, JBL engineers have created a unique, direct voice coil-to-air heat dissipation method called Vented Gap Cooling.

This process pumps air through the magnetic gap and directly over and around the voice coil to provide immediate heat transfer and reduction in operating temperature - a direct improvement in power compression.

Through the use of new computeraided magnet optimization and analysis techniques, JBL engineers were able to optimize both magnet weight, flux density and field saturation resulting in a 1.8 kg (3.9 lb) reduction in overall driver weight and a significant reduction in harmonic distortion. This new magnet structure offers much of the weight advantage of rare earth magnet structures without their prohibitive cost.

Specifications:

Nominal Diameter: 300 mm (12 in)

Rated Impedance: 8 ohms

Power Capacity1: 600 W continuous pink noise

Sensitivity 2: 95 dB SPL, 1 W, 1 m (3.3 ft)

Frequency Range3: 45 Hz 3.5 kHz.

Power Compression4

at - 10 dB power (60 W): 0.6 dB

at - 3 dB power (300 W): 2.4 dB

at full power (600 W): 3.9 dB

Distortions

2nd harmonic: < 1.0%

3rd harmonic: < 1.0%

Highest Recommended Crossover: 1500 Hz

Recommended Enclosure Volume: 28-113 1 (1-4 ft3)

Effective Piston Diameter: 264 mm (10.4 in)

Maximum Excursion Before

Damage (p-p): 40 mm (1.6 in)

Minimum Impedance: 6.9 ohms ± 10% @ 25°C (H)

12.2 ohms ± 10% @ 25°C (J)

Voice Coil Diameter: 100 mm (4 in)

Voice Coil Material: Edgewound aluminum ribbon

Voice Coil Winding Depth: 19 mm (0.75 in)

Magnetic Gap Depth: 8 mm (0.32 in)

Magnetic Assembly Weight: 6.8 kg (15 lb)

B1 Factor: 18.1 N/A(H)

24.8 N/A (J)

Effective Moving Mass: 0.065 kg

Positive voltage on BLACK terminal gives forward diaphragm motion.

AES standard (60-600 Hz).

Sensitivity is based on a swept 100 Hz to 500 Hz signal. 1 W is 2.83 V @ 8 ohms, 4.0 Vat 16 ohms.

Frequency range is defined as the frequency extremes where the response is - 10 dB from the rated sensitivity.

Power compression is the sensitivity loss at the specified power, measured from 60 to 600 Hz, after a 5 minute AES

standard (60-600 Hz) pink noise preconditioning test at the specified power.

Distortion is measured at - 10 dB power, from 100-500 Hz.

JBL continually engages in research related to product improvement New materials, production methods, and design

refinements are introduced into existing products without notice as a routine expression of that philosophy. For this

reason, any current JBL product may differ in some respect from its published description but will always equal or

exceed the original design specifications unless otherwise stated.

These JBL parts are original Factory Parts. We sell only GENUINE JBL PARTS. Some other dealers sell INFERIOR aftermarket parts. In order to return your speaker to FULL FACTORY PERFORMANCE Specs Genuine parts are needed. If the part that you're looking for is not here, please call us Toll-Free at 877-776-7631 and we will find it for you.